پنهنجن ٻارن لا هڪ اهڙو بال (رانديڪو) ٺاهيو جيڪو اوندهه ۾ ٻري

پنهنجن ٻارن لا هڪ اهڙو بال (رانديڪو) ٺاهيو جيڪو اوندهه ۾ ٻري

 

اچو ته ڏسون ته هي ٻارن جو پروجيڪٽ ٺاهڻ لاِ ڪهڙا سامان کپندا

We are selective in our materials for cost, ease of use, and safety due to our high traffic (800,000 visitors annually). So, for our purposes, this design worked best. But you may have other ideas - please share!

• 1 - CR2032 Coin Battery (available at most stores, but we purchase ours in bulk from Batteries and Butter)
• 1 - LED (available at Radio Shack, etc., but we purchase ours in bulk fromLeading LEDs)
• 1 - 12” x 12” Piece of bubble wrap (we get ours in bulk from U-Line, but you probably have some lying around somewhere you can use. If not, go buy yourself something nice and use THAT bubble wrap
• Tape
• Scissors

 

ببل ريپر مارڪيٽ ۾ اليڪٽرانس شاپ تان آرام سان ملي ويندي، هي مشينن يا وڏن ننڍن پُرزن کي حفاظت سان پاڪنگ ڪيل هوندا اهن هي اهڙيون پلاسٽڪ ريپر شيٽون هونديون آهن جن جي وچ ۾ ميٽرڪس وانگر هوا ڀريل هوندي آهي۔ اچو ته ڏسون ته ان شيٽ کي حاصل ڪري ڪيئن فولڊ ڪري پنهنجو بال ٺاهڻ گهُرجي۔ ۽ ڪيئن اُن ۾ پنهنجو سرڪٽ وجهڻ گهرجي۔






With the bubble side up, fold the bottom right corner of the bubble wrap to the center. Fold the other three corners to center. Tape the corners together in the center. Roll the bubble wrap into a tube and tape the seam so it doesn't unroll.

 

Step 4: Step 2 - Roll the Bubble Wrap

Roll the bubble wrap into a tube and tape the seam so it doesn't unroll.

 

Step 5: Step 3 - Prepping the LED

Find the long and the short wire coming off the LED. Slide the LED over the battery with the long wire on the “+” side of the battery and the short wire on the other side of the battery.



If the LED doesn’t light up, try flipping the battery over before taping. Use masking tape to tightly tape the short wire from the LED to the back of the battery, leaving a space of wire close to the LED free

Bend the long wire slightly away from the “+” side of the battery.

 

Step 6: Step 4 - Putting It All Together



With the long wire facing up, tape the short lead from the LED down to one end of the bubble wrap tube

Starting at the end with the LED, roll the bubble wrap from the left to the right to form a smaller ball shape.

Gently squeeze the ball and make sure the LED turns on. If not, adjust the LED and re-roll the ball. Tape the ball shut so the LED is just barely off.

 

Step 7: To Use
To use, squeeze the bubble wrap ball to turn on the LED. It looks best in the dark. You can even add velcro tape so you can turn it "on" or "off" by adjusting how tight the velcro is.

For an educational environment: the LED Bubble Wrap Ball works because of the “squeeze switch” inside. In order for any electrical circuit to work, it needs three parts: a power source (battery), a path for energy to flow (leads), and an output (LED). The circuit inside the Bubble Ball is open (or “off”) until you squeeze it and press the long lead to the battery.

This closes (or turns “on”) the circuit, allowing the electrical energy to flow from the battery through the leads to the LED, turning on the light. Also, the LED Bubble Wrap Ball lights up nicely because the light undergoes refraction and diffusion as it passes through the bubble wrap.